No Predrilling The Type-17 point starts fast and drives cleanly into wood, so you spend less time drilling pilot holes and reduce the chance of splitting. Built for Connector Work This Simpson Strong-Tie heavy-duty connector screw is made for structural connector installations where holding strength, repeatable installation, and reliable fit matter. Exterior-Ready Coating The Double-Barrier coating helps resist corrosion in exterior wood applications, which matters when fasteners are exposed to weather over time.
The Simpson Strong-Tie SDS25300MB Strong-Drive SDS Heavy-Duty Connector Screw is a 1/4 in. x 3 in. structural wood screw sold in a 150-count pack. This is a heavy-duty connector screw designed for structural connector installation and wood-to-wood fastening in exterior wood applications. Model Number: SDS25300MB. If you need a fastener for Simpson Strong-Tie connectors that installs faster than a lag and does not force you into predrilling on every hole, this is the one you look at first.
For this exact variant, you are getting a 3 in. screw with a 0.235 in. shank diameter, serrated threads, a 2 in. thread length, and a Type-17 point. On the job, that combination means easier starts, cleaner driving, and solid pull-down into the lumber. The serrated threads help the screw bite and seat without fighting you the whole way in, which is a real time saver when you are running repeated connector installs.
The head design matters here too. Simpson uses a 3/8 in. hex head with a 0.500 in. integrated washer, so you get a broad bearing surface without needing a separate washer. That helps spread load at the connection and gives you a secure, positive drive interface that is less likely to cam out compared to many common screw heads. The head is also stamped with the Simpson Strong-Tie mark and fastener length for easier identification after installation, which is a small detail that helps when you are checking work later.
This fastener uses a Double-Barrier coating over high-strength carbon steel for corrosion resistance in exterior wood applications. That is important for deck work, outdoor framing details, and connector installations where the fastener is part of the long-term durability of the assembly. If you are matching the fastener to exterior-rated hardware and want better corrosion protection than a basic interior screw, this coating is part of why the SDS line is widely specified.
Installation is straightforward. Simpson recommends a low-speed 1/2 in. drill with a 3/8 in. hex driver for installation. In plain terms, that means this screw is intended to be driven with controlled torque and good engagement at the head. That makes sense for structural fastening, where consistent seating matters more than just running screws as fast as possible. The Type-17 point helps it go in without predrilling in many wood applications, which cuts down install time and helps limit splitting.
The SDS platform is built around connector work, not just general-purpose wood screw duty. Simpson specifically calls out heavy-duty Simpson Strong-Tie connectors, and the product description also notes use in wood-to-wood and engineered wood applications. So while this screw can absolutely handle demanding fastening in lumber, its real value is that it is engineered around connector installations where published load values and hardware compatibility matter.
For buyers comparing options, this is the practical middle ground between slower traditional structural fastening methods and lighter-duty screws that are not intended for connector use. The 1/4 in. diameter gives it real structural presence, while the no-predrill Type-17 point keeps installation efficient. That is why contractors use these for deck framing details, exterior connector fastening, beam and hanger hardware, and other places where strength and speed both count.
If you are a deck builder, framer, remodeler, carpenter, or serious DIYer working with Simpson hardware, the Simpson Strong-Tie SDS25300MB Strong-Drive SDS Heavy-Duty Connector Screw makes a lot of sense. It is especially well suited for exterior fastening, connector installation, and structural wood connections where you want a fast, repeatable install with a hex head you can really lean on.
This screw is built to move connector and deck work along without adding extra steps. The Type-17 point helps it start cleanly, so you can drive into wood without stopping to predrill in many applications.
Not every structural screw is meant for connector hardware. This one is. The SDS line is intended for heavy-duty Simpson Strong-Tie connectors, so you are choosing a fastener designed around that use instead of forcing a general-purpose screw into a structural role.
The 3/8 in. hex head gives you positive engagement when you are seating structural fasteners into framing members and hardware. Add the integrated washer, and you get strong bearing at the head without a separate part to keep track of.
Exterior wood projects live outside, and the fastener has to keep up. The Double-Barrier coating is there to help resist corrosion in outdoor use, making this a better fit for exposed framing and exterior connector jobs than a basic interior screw.
Driver bit is not listed as included with this SDS25300MB pack. Replacement driver bit: BITHEXR38-R1.
| Diameter | 1/4 in. |
|---|---|
| Length | 3 in. |
| Shank Diameter | 0.235 in. |
| Drive Type | 3/8 in. Hex |
| Head Type | Hex Head with 0.500 in. Integrated Washer |
| Thread Type | Serrated Threads |
| Thread Length | 2 in. |
| Point Type | Type-17 Point |
| Coating | Double-Barrier Coating |
| Material | High-Strength Carbon Steel |
| Packaging Quantity | 150 |
| UPC | 707392976103 |
Driver Interface Uses a 3/8 in. hex drive interface. Recommended Installation Tool Simpson recommends a low-speed 1/2 in. drill with a 3/8 in. hex driver. Replacement Driver Bit Replacement driver bit: BITHEXR38-R1. Primary Application Fit Designed for heavy-duty Simpson Strong-Tie connectors, plus wood-to-wood and engineered wood fastening applications.
Deck Building Carpentry Construction Remodeling Exterior Fastening Structural Connector Installation Wood-to-Wood Fastening Engineered Wood
Use a low-speed 1/2 in. drill with a 3/8 in. hex driver like Simpson recommends. These structural screws seat more consistently when you drive them with control instead of trying to hammer them in at full speed.
Tool Nut’s Take
This is the kind of structural screw pros buy when they want connector installs to go faster without giving up confidence in the connection.
More styles you’ll love.
Reviews (0)
There are no reviews yet.